Split nylon flange bushings fit over clutch pedal cross shaft and inside cross shaft sleeve for clutch and brake pedals with 5/8" diameter cross shaft. These OER® reproduction bushings will help eliminate excessive side to side…
Set of four reproduction pedal shaft bushings. Used with all automatic and manual pedals. Group 0.831 and 4.626 GM Part #: 3798256, 3965692, 1247439, 140048221…
The clutch cross shaft is a piece of steel that slides into the transmission case, and it is the pivot point for the fork that pushes onto you clutch diaphragm. Basically, if it were to fall out you wouldn't be able to operate the clutch…
Best Quality Reproduction Bellcrank Seals Heavy, Die Cut Felt Fiber As Original Keeps Grease In The Clutch Bellcrank Where It Belongs 9/16 ID & 1? OD This little Camaro part does a big job and will wear out easily from years of use and…
Stock Replacement Original GM Seals Z-Bar At Frame Side Ball Stud Keeps Debris From Entering Z-Bar Causing Pre Mature Ware This stock replacement ball stud dust seal is manufactured by GM or by one of its authorized suppliers for use as a…
Stock Replacement Original GM Retains Swivel To Z-Bar And Clutch Pedal To Upper Rod This stock replacement clutch linkage retainer clip is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You…
Stock Replacement Original GM Correct Spring For Ball Stud On Frame Side This stock replacement ball stud spring is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit and…
Stock Replacement Original GM 4 Needed Per Brake And Clutch Pedal Support Bolt Featured In 1978-87 Clutch Linkage Diagram As Number 13 Featured In 1959-77 Clutch Linkage Diagram As Number 2 Will Not Replace Large White Bushing On 1959-1960…
Stock Replacement 2nd Design Ball, Is A 1/4 Inch Shorter Then 1st Design Will Replace 1st Design Ball Studs This stock replacement ball stud is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part…
Authentic hardware you need to correctly reassemble the transmission components. Most fasteners have correct markings for the time period. This kit includes one retaining clip.
…
Reproduction Of Original Includes Integral Rubber Seal This Chevelle reproduction clutch bellcrank pivot stud has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit and…
Accurately machined Frame pivot ball stud fits all original and reproduction big and small block clutch bellcranks. Unlike cheap knock-offs offered elsewhere, ours are heat treated for hardness as original. Black oil finish. Overall length…
Stock Replacement Original GM Correct Foam Rubber Seal Pre Attached Featured In 1978-87 Clutch Linkage Diagram As Number 35 This stock replacement clutch fork ball stud is manufactured by GM or by one of its authorized suppliers for use as…
Reproduction Of Original Welds To Lower Firewall Used To Anchor Bellcrank Spring To Firewall This Chevelle reproduction clutch bellcrank firewall return spring bracket on firewall has been manufactured to original factory specifications…
Reproduction Of Original Correct Short Bracket Weld To Frame This Chevelle reproduction pivot bracket has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and…
Reproduction Of Original Correct Retaining Ring For Boot P/N 02-1530 Sold Separately This El Camino reproduction firewall clutch boot retainer has been manufactured to original factory specifications using today's modern manufacturing…
Reproduction Of Original Correct Retaining Ring For Boot P/N 02-1510 Sold Separately This El Camino reproduction firewall clutch boot retainer has been manufactured to original factory specifications using today's modern manufacturing…
Reproduction Of Original This El Camino reproduction clutch spring has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for…
Reproduction Of Original This El Camino reproduction clutch retainer pin has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit and function will work superbly for your…
Best Quality Reproduction Brake Or Clutch Pedal Bushings Fits Chevy El Camino, GMC Sprint & Caballero Complete Set Of 4 Featured In 1978-87 Clutch Linkage Diagram As Number 13 Will Not Replace Large White Bushing On 1959-1960 If you…
Stock Replacement Original GM Correct White Nylon Bushing 2 Needed Per Ball This stock replacement clutch ball seal is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit…
Reproduction Of Original This Chevelle & Malibu reproduction clutch bellcrank pivot ball has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function…
Reproduction Of Original Welds To Lower Firewall Used To Anchor Z-Bar Spring To Firewall This El Camino reproduction z-bar return spring bracket has been manufactured to original factory specifications using today's modern manufacturing…
Replacement Of Original Featured In 1978-87 Clutch Linkage Diagram As Number 43 This El Camino replacement z-bar dust seal has been manufactured to meet or exceed factory specifications and performance. You will find the fit and function…
Stock Replacement Correct Washer For The Z-Bar Support Bracket To Ball Featured As #7 In 1959-1977 Clutch Linkage Diagram In The Catalog This stock replacement clutch z-abr support bracket washer is manufactured by GM or by one of its…