Used with all GM or reproduction clutch bellcranks. Three nylon pivot ball seats (only two required) and spring steel retainer clip. For small or big block bellcranks. GM Part #: Seat 3743349, Clip 3750696…
Manufactured to meet or exceed all original OEM specifications. Correct for small or big block. Exact replacement. Unlike others offered, ours functions perfectly for listed applications. GM Group #: 0.795 GM Part #: 3892632
…
Retaining clip for clutch pedal on manual transmision cars and 5/8" pin on automatic transmision cars. One required per car. Clip is included on cluch and brake pedal assembly (W-597, W-598 & W-839). Group 0.837 & 4.634 GM Part #…
Engineered and manufactured for reliability, these alloy steel flywheel bolts are heat treated to grade 8 specifications for extra strength. Kits are complete with lock washers, where needed, and are black plated to help resist rust and…
Quality Reproduction Molded Rubber Boot Includes Internal Metal Washer As Original The clutch upper pushrod firewall boot keeps air and dust from flowing through the firewall of your Chevelle and it is a part which is prone to wear out. …
Set of four reproduction pedal shaft bushings. Used with all automatic and manual pedals. Group 0.831 and 4.626 GM Part #: 3798256, 3965692, 1247439, 140048221…
The spring sets comes with the large clutch return spring that goes from the Z-Bar to the frame bracket as well as a small anti-rattle spring that goes from the Z-Bar to the clutch fork (on some applications) to keep the components from mak…
Reproduction Of Original Three Piece Set This Chevelle reproduction bell crank lower push rod has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and…
Best Quality Reproduction Officially Licensed GM Restoration Part Correct Spun Molded Unit Metal Retaining Plate Available Separately This clutch boot assembly is 100% correct. This is the boot that installs on the firewall in the engine…
OER® reproduction of the original die-cut seal that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Applications 1967-69 Camaro 1963-67 Chevrole t/GMC Truck 1959-60…
Stock Replacement Original GM Seals Z-Bar At Frame Side Ball Stud Keeps Debris From Entering Z-Bar Causing Pre Mature Ware This stock replacement ball stud dust seal is manufactured by GM or by one of its authorized suppliers for use as a…
The clutch fork takes a lot of abuse over the years by moving the throw out bearing away from the clutch over and over again literally thousands of times! Stress cracks can form on either end of the fork as well as the fulcrum pivot point…
Stock Replacement Original GM Retains Swivel To Z-Bar And Clutch Pedal To Upper Rod This stock replacement clutch linkage retainer clip is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You…
Reproduction Of Original This Chevelle reproduction z bar has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
Stock Replacement
Attaches Clutch Pedal To Z-Bar Through The Firewall
This stock replacement upper clutch rod is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You…
Stock Replacement Original GM Correct Spring For Ball Stud On Frame Side This stock replacement ball stud spring is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit and…
Stock Replacement 2nd Design Ball, Is A 1/4 Inch Shorter Then 1st Design Will Replace 1st Design Ball Studs This stock replacement ball stud is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part…
Authentic hardware you need to correctly reassemble the transmission components. Most fasteners have correct markings for the time period. This kit includes one retaining clip.
…
Reproduction Of Original Works With All GM & Reproduction Bellcranks This Camaro reproduction clutch bellcrank pivot kit has been manufactured to original factory specifications using today's modern manufacturing techniques. You will…
Accurately machined Frame pivot ball stud fits all original and reproduction big and small block clutch bellcranks. Unlike cheap knock-offs offered elsewhere, ours are heat treated for hardness as original. Black oil finish. Overall length…
Reproduction Of Original Attaches Clutch Pedal To Z-Bar Through The Firewall Correct Sharp Bent Ends Officially Licensed Gm Restoration Part This El Camino reproduction upper clutch rod has been manufactured to original factory…
Reproduction Of Original Correct Spun Molded Unit With Integrated Metal Retaining Plate Featured In 1978-87 Clutch Linkage Diagram As Number 22 This clutch boot assembly is 100% correct. This is the boot that installs on the firewall in…
Reproduction Of Original This El Camino reproduction clutch bellcrank upper push rod firewall boot has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and…
Stock Replacement Original GM Correct Foam Rubber Seal Pre Attached Featured In 1978-87 Clutch Linkage Diagram As Number 35 This stock replacement clutch fork ball stud is manufactured by GM or by one of its authorized suppliers for use as…