Reproduction Of Original Kit Includes All Necessary Bolts, Nuts, & Washers Easy Installation The gas tank on your 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, or 1972 Chevelle gets used quite often over the years as long as you…
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is 3/8", bolt not…
Our 1969 Camaro vented gas cap allows harmful vapors to escape without causing harm to you fuel tank. You'll also avoid annoying fuel blowback. We've got you covered.
…
OER® reproduction of the original grommet and sleeve unit where the accelerator rod fits into linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will keep your throttle rod from…
Restoration Correct Gas Tank Straps Correct Galvanized Finish Correct Length And Bend One Set Required Per Car Bolt Set Available Separately, Part # 607924 H ave the gas tank straps on your 1968, 1969, 1970, 1971 or 1972 Chevelle began to…
This molded plastic grommet is an identical reproduction of original equipment and is designed to keep the accelerator cable from pulling through the pedal linkage. Sold per each, the grommet snaps into the accelerator pedal linkage and is…
Reproduction Of Original Indicates Fill Line & Fuel Level Replaces Worn Sending Unit Gasket, Keeping Unit Secure While many may not be aware, the sending unit of your 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, or 1972 Chevelle?s…
Reproduction of Original Throttle Rod Bushing & Sleeve (1) Rubber Bushing (1) Plastic Sleeve See More Photos for Placement Diagram The frugal minded Chevelle owner would install this bushing and sleeve into the throttle arm to keep…
Reproduction Of Original Locks Sending Unit To The Fuel Tank This Chevelle reproduction lock ring has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit and function…
These are exact reproductions guaranteed to perform flawlessly. The 1964-72 reproduction units are made from stainless steel while 1973 units are galvanized steel. All sending units include O-ring for sealing as well as 1/4" return line…
Restoration Correct
Durable Molded Rubber Construction
Fits Into Trunk Pan
Supports Fuel Vent Tubes
1964-1972 Chevelle and Malibu is a classic car for a full restoration or building that ground pounding street…
Our authentically reproduced mounting straps are a must when installing your fuel tank. Available in galvanized, stainless or factory correct black zinc coating which inhibits corrosion. These steel straps are formed to factory…
Reproduction Of Original This Chevelle reproduction gas cap has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
Holley mechanical fuel pumps range from 80 GPH to 225 GPH in many various applications to meet the fuel demands of most engines. Whether you are looking for a street performance or an all out race mechanical fuel pump, Holley has the pump…
This molded plastic grommet is an identical reproduction of original equipment and is designed to keep the accelerator cable from pulling through the pedal linkage. Sold per each, the grommet snaps into the accelerator pedal linkage and is…
Reproduction Of Original Correct Stud Used On All Holley Four Barrel Carburetors With Cowl Induction System This Chevelle reproduction carburetor stud has been manufactured to original factory specifications using today's modern…
Correct Reproduction Throttle Rod Modeled After BB Rod For Use With Rochester 4 bbl Carburetor Includes Correct Swivel Correct reproduction of original BB rod for use with Rochester 4 bbl carbs. Includes correct swivel.
…